2205mm Recessed Concrete Post

Rapid setting post hole concrete, suitable for fixing all types of wooden, metal and concrete posts.

Post Mix is a pre-blended, quick setting concrete mix, which sets in approximately 10 minutes after mixing with water (depending on ambient temperature).
Simply half fill the hole with water, then pour the post mix in.

Fencing contractors typically allow 1½ to 2 bags per fence post (this varies depending on the hole and post size).

We offer 33% discount on post-mix when you pay & collect in store!

These concrete gravel boards are designed to be used with recessed concrete posts. Concrete gravel boards for recessed posts give feather edge fencing a level surface to sit on. Raising feather edge boards on a gravel board will help prevent rot caused by ground moisture, gravel boards also help to prevent damage to fence panels caused by lawn mowers and strimmers.

- Dimensions: 50mm x 150mm x 2400mm
- 40kg Each
- C50 Concrete (a strong mix)
- Two 5.5mm rebar set inside
- One 14mm diameter hole in the middle to attach a support post (if required)

These concrete gravel boards are designed to be used with recessed concrete posts. Concrete gravel boards for recessed posts give feather edge fencing a level surface to sit on. Raising feather edge boards on a gravel board will help prevent rot caused by ground moisture, gravel boards also help to prevent damage to fence panels caused by lawn mowers and strimmers.

- Dimensions: 50mm x 150mm x 3000mm
- 52kg Each
- C50 Concrete (a strong mix)
- Two 5.5mm rebar set inside
- One 14mm diameter hole in the middle to attached a support post (if required)

Timber carcassing, general purpose building timber.

- Machined from 47 x 150mm, finished size approx. 45 x 145mm
- Smooth regularised finish
- Grade C24
- Good quality, slow-grown softwood
- Pressure-treated green

Treated carcassing timber conquers outdoor projects!
- Machined from 47 x 150mm, finished size approx. 45 x 145mm
- Smooth finish and C24 graded
- Premium quality, slow-grown softwood
- Pressure-treated green for durability

Treated timber carcassing.
- Machined from 47 x 150mm, finished size approx. 45 x 145mm
- Smooth regularised finish
- Grade C24
- Good quality, slow-grown softwood
- Pressure-treated green

Our carcassing timber is pressure-treated for extended lifespan and protection against insect and fungal attacks.

Sourced from responsibly managed forests in Europe, the majority of our carcassing is milled in Sweden or Latvia where due to the colder climates the timber is slow grown resulting in a denser, straighter end product.

- Machined from 47 x 75mm, finished size approx. 45 x 70mm
- Smooth regularised finish
- Grade C16 / C24 - mixed
- Good quality, slow grown softwood
- Pressure treated green

Treated carcassing timber for general purpose building.
- Machined from 47 x 75mm, finished size approx. 45 x 70mm
- Smooth regularised finish
- Grade C16 / C24 - mixed
- Good quality, slow grown softwood
- Pressure treated green

Premium treated timber carcassing for general purpose building projects.
- Machined from 47 x 75mm, finished size approx. 45 x 70mm
- Smooth regularised finish
- Grade C16 / C24 - mixed
- Good quality, slow grown softwood
- Pressure treated green

125mm Feather Edge Boards are tapered boards that are vertically lapped to form a solid fence.
Feather-edge can also be fitted horizontally as a budget cladding.

- 125mm Board Width
- 10 boards needed per linear metre (25mm overlap)
- Cut from 22 x 125mm
- Finished size approx. 12mm on thick edge tapering to 6mm on thin edge
- Homegrown Spruce
- Sawn finish
- Pressure treated green

Enhance your Feather Edge fence with our Rebated Fence Capping, crafted from premium Scandinavian Redwood. Providing both a quality finishing touch and additional protection, this capping is pressure treated green for longevity. See full product description below.

Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.

Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.

Supplied with one standard hex nut, washers sold separately.

Steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.

Dimensions: 1.5mm x 21mm Diameter
9mm Bolt Hole: To suit M8 thread

Traditional annular ringshank nails for fixing timber to timber. The threaded shank increases pull out resistance, large head for increased holding power.

Nail Length: 50mm
Nail gauge: 2.65mm
Average nail count = 350 /kg
Finish: Sherardised, service class 2 according to EN 14592:2008
Manufactured to BS 1202-1

Traditional annular ringshank nails for fixing timber to timber. The threaded shank increases pull out resistance, large head for increased holding power.

Nail Length: 50mm
Nail gauge: 2.65mm
Average nail count = 350 /kg
Finish: Sherardised, service class 2 according to EN 14592:2008
Manufactured to BS 1202-1

Traditional annular ringshank nails for fixing timber to timber. The threaded shank increases pull out resistance, large head for increased holding power.

Nail Length: 50mm
Nail gauge: 2.65mm
Average nail count = 350 /kg
Finish: Sherardised, service class 2 according to EN 14592:2008
Manufactured to BS 1202-1

Traditional annular ringshank nails for fixing timber to timber. The threaded shank increases pull out resistance, large head for increased holding power.

Nail Length: 50mm
Nail gauge: 2.65mm
Average nail count = 350 /kg
Finish: Sherardised, service class 2 according to EN 14592:2008
Manufactured to BS 1202-1