Nails & Staples

Light-duty nails /pins suited to fixing small decorative components; timber to timber. Small head for flush finish.

Pin length: 40mm
Pin gauge: 1.6mm
Average pin count = 1590 /kg (½ kg bag)
Finish: Sherardised, service class 2
Manufactured to BS EN 10230-1

Traditional round wire nails for fixing timber to timber. Large head for increased holding power.

Nail Length: 40mm
Nail gauge: 2.65mm
Average nail count = 575 /kg
Finish: Galvanised, service class 3 according to EN 10016-2
Manufactured to BS EN 10230-1

Cut point staples, typically used for attaching wire and netting to timber.

Staple length: 40mm
Staple gauge: 4.0mm
Average staple count = 136 /kg
Finish: Galvanised, service class 3

Stainless steel annular ringshank nails for fixing timber to timber. The threaded shank increases pull out resistance, large head for increased holding power.

Nail Length: 38mm
Nail gauge: 2.65mm
Average nail count = 350 /kg
Material: A2 Stainless steel, service class 3
Manufactured to BS 1202-1

Stainless steel nails with a serrated annular ring pattern along the shank; for extra pull-out resistance. This is the correct nail for installing Cedar Shingles. The clout head firmly secures shingles and helps to prevent the nail being over-driven or pulled through the timber by strong winds.

31mm x 1.8mm Stainless Steel Ring Clout Nail
1kg pack = approximately 1500 nails
1kg of nails will install approximately 4 bundles of Cedar Shingles

Square twisted nails; the recommended fixing for installation of joist hangers.

Nail length: 30mm
Nail gauge: 3.75mm
Average nail count = 350 /kg
Finish: Sherardised, service class 2

Cut point staples, typically used for attaching wire and netting to timber.

Staple length: 30mm
Staple gauge: 3.55mm
Average staple count = 260 /kg
Finish: Galvanised, service class 3

Light-duty nails /pins suited to fixing small decorative components; timber to timber. Small head for flush finish.

Pin length: 25mm
Pin gauge: 1.6mm
Average pin count = 2340 /kg (½ kg bag)
Finish: Sherardised, service class 2
Manufactured to BS EN 10230-1

Cut point staples, typically used for attaching wire and netting to timber.

Staple length: 25mm
Staple gauge: 2.65mm
Average staple count = 486 /kg
Finish: Galvanised, service class 3

Cut point staples, typically used for attaching wire and netting to timber.

Staple length: 20mm
Staple gauge: 2.0mm
Average staple count = 1079 /kg
Finish: Galvanised, service class 3

Traditional round wire nails for fixing timber to timber. Large head for increased holding power.

Nail Length: 150mm
Nail gauge: 6.0mm
Average nail count = 29 /kg
Finish: Galvanised, service class 3 according to EN 10016-2
Manufactured to BS EN 10230-1

Traditional round wire nails for fixing timber to timber. Large head for increased holding power.

Nail Length: 150mm
Nail gauge: 6.0mm
Average nail count = 29 /kg
Finish: Galvanised, service class 3 according to EN 10016-2
Manufactured to BS EN 10230-1

Short galvanised nails with an extra large clout head, designed for fixing down shed felt.
Approximately 345 nails per 500g pack.

Traditional round wire nails for fixing timber to timber. Large head for increased holding power.

Nail Length: 125mm
Nail gauge: 5.6mm
Average nail count = 42 /kg
Finish: Galvanised, service class 3 according to EN 10016-2
Manufactured to BS EN 10230-1

Traditional round wire nails for fixing timber to timber. Large head for increased holding power.

Nail Length: 100mm
Nail gauge: 4.5mm
Average nail count = 77 /kg
Finish: Galvanised, service class 3 according to EN 10016-2
Manufactured to BS EN 10230-1