Search
Mon-Fri: 8am to 5pm | Sat: 8am to 12pm | Sun: Closed
Show Prices Inc VAT
Product Catalogue
    Menu Close
    banner

    Hinges

    View as Grid List
    Sort by
    Display per page
    Picture of 100mm ADJUSTABLE GATE EYE + 2 NUTS - B.Z.P.

    100mm ADJUSTABLE GATE EYE + 2 NUTS - B.Z.P.

    Designed for field and farm gates, these gate eyes are compatible with our wide range of gate hooks. When using for steel gates, adjustable gate eyes can be bolted directly through the gate stile & the included nuts tightened each side, but for timber gates an adjustable bottom fitting is commonly used.
    £3.71 incl VAT
    Picture of 100mm BRUSHED STAINLESS STEEL BALL BEARING BUTT HINGE CLASS 13 - PAIR

    100mm BRUSHED STAINLESS STEEL BALL BEARING BUTT HINGE CLASS 13 - PAIR

    Grade 316 Stainless Steel ball bearing butt hinges with screws included.
    Ideal for hanging internal doors, these hinges conform to BS EN1935 & are fire rated for use on 30 minute & 1 hour fire doors.
    £6.68 incl VAT
    Picture of 125mm BOTTOM BAND

    125mm BOTTOM BAND

    An alternative to the adjustable bottom gate fitting, this item is galvanised.
    £9.20 incl VAT
    Picture of 125mm DOUBLE STRAP FIELD GATE BOTTOM BAND WITH OFFSET EYE ON CORNER (SPECIAL ORDER)

    125mm DOUBLE STRAP FIELD GATE BOTTOM BAND WITH OFFSET EYE ON CORNER (SPECIAL ORDER)

    Specialist gate hinges with the eyes on the corner of the hinge.
    The off set hinge has the eye set at approximately 45 degree angle from the corner of the hinge.

    Hanging pins & fixings are sold separately.
    £13.15 incl VAT
    Picture of 125mm DOUBLE STRAP FIELD GATE BOTTOM BAND WITH STRAIGHT EYE ON CORNER (SPECIAL ORDER)

    125mm DOUBLE STRAP FIELD GATE BOTTOM BAND WITH STRAIGHT EYE ON CORNER (SPECIAL ORDER)

    Specialist gate hinges with the eyes on the corner of the hinge.
    Hanging pins & fixings are sold separately.
    £14.89 incl VAT
    Picture of 150mm E-GALV. LIGHT T- HINGES

    150mm E-GALV. LIGHT T- HINGES

    Suitable for light duty applications, these bright zinc plated hinges are popular for use in animal housing, eg. chicken runs, hutches etc.
    £1.14 incl VAT
    Picture of 19mm ADJUSTABLE GATE HANGER ON 100 X 100mm PLATE

    19mm ADJUSTABLE GATE HANGER ON 100 X 100mm PLATE

    This adjustable gate hanger has a 19mm pin and is galvanised for corrosion resistance. Typically used for fitting pairs of wooden five bar gates to timber gate posts, the adjustable hook length enables the fitter to easily make sure that the gates line up perfectly in the middle. The 100x100mm fixing plate has four holes for screws or bolts.
    £12.46 incl VAT
    Picture of 19mm FIELD GATE HOOK TO DRIVE

    19mm FIELD GATE HOOK TO DRIVE

    This 19mm hook to drive is normally used for fitting the bottom part of a standard field gate hinge to a timber gate post. The 19x19x175mm square spike is designed to be driven in with a club/ sledge hammer. This enables the fitter to easily adjust the length of the hook in order to make the gate plumb. A pilot hole must be drilled to avoid splitting the post. Galvanised to prevent rust.
    £4.40 incl VAT
    Picture of 19mm GATE HANGER ON 100 X 100mm PLATE

    19mm GATE HANGER ON 100 X 100mm PLATE

    Galvanised for corrosion resistance, this 19mm gate pin has 4 bolt holes for a very secure fixing.
    £6.90 incl VAT
    Picture of 19mm GATE HANGER ON OBLONG PLATE

    19mm GATE HANGER ON OBLONG PLATE

    Galvanised for corrosion resistance, this 19mm gate pin has 2 bolt holes on a 50 x 200mm plate.
    £11.03 incl VAT
    Picture of 19mm GATE HANGER TO BUILD IN

    19mm GATE HANGER TO BUILD IN

    19mm gate hanger designed to be built into brickwork. This item is galvanised for corrosion resistance.
    £19.36 incl VAT
    Picture of 19mm HOOK TO SCREW

    19mm HOOK TO SCREW

    This hook to screw has a 19mm pin to fit a standard field gate hinge, to a timber gate post. The pin has a hole at the top to fit a small bolt to stop the gate being lifted off the hinge. The 18x190mm screw thread enables the fitter to easily adjust the length of the hook in order to make the gate plumb, which is ideal if re-using old posts that have moved over time. A pilot hole must be drilled to avoid splitting the post. Galvanised to prevent rust.
    £4.93 incl VAT
    Picture of 19mm x 275mm FIELD GATE HOOK TO BOLT

    19mm x 275mm FIELD GATE HOOK TO BOLT

    This 19mm hook to bolt is normally used for fitting the top part of a standard field gate hinge to a timber gate post. Suitable for posts between 125mm to 200mm. Galvanised to prevent rust.
    £6.95 incl VAT
    Picture of 19mm x 300mm FIELD GATE HOOK TO BOLT - BRICKWORK

    19mm x 300mm FIELD GATE HOOK TO BOLT - BRICKWORK

    This 19mm hook to bolt is used for hanging field gates from a brick pillar without having to secure timber to the pillar first.
    £9.43 incl VAT
    Picture of 250mm ADJUSTABLE GATE EYE + 2 NUTS - B.Z.P.

    250mm ADJUSTABLE GATE EYE + 2 NUTS - B.Z.P.

    Designed for field and farm gates, these gate eyes are compatible with our wide range of gate hooks. When using for steel gates, adjustable gate eyes can be bolted directly through the gate stile & the included nuts tightened each side, but for timber gates an adjustable bottom fitting is commonly used.
    £6.95 incl VAT