Fixings & Metalwork

A quality Post Base made by Simpson Strong-Tie. Used to raise timber posts and timber framework above ground level, which prevents rotting caused by moisture from ground contact. Suitable for structurally supported timber posts and framework that need to last a long time e.g. for a basic timber porch or decking framework. Not recommended for free standing posts e.g. fence posts.

- Steel S235JR according to NF EN 10025
- Hot-dip galvanized according to NF EN ISO 1461
- Total Height - 100mm
- Tubular Core - 48mm diameter
- Top plate - 100 x 100mm x 4mm
- Base plate - 130 x 130mm x 4mm
- Maximum post cross section - 200 x 200mm
- 11.0mm fixing holes (x8)

A quality Post Base made by Simpson Strong-Tie. Used to raise timber posts and timber framework above ground level, which prevents rotting caused by moisture from ground contact. The height/level of the square support plate can easily be adjusted after installation which is useful when building structures on uneven ground. Suitable for structurally supported timber posts and framework that need to last a long time e.g. for a basic timber porch or decking framework. Not recommended for free standing posts e.g. fence posts.

- Dichromate coated galvanised mild steel
- Height Adjustable: 100mm→150mm
- Threaded Core: 20mm diameter
- Top plate: 100 x 100mm x 5mm
- Base plate: 130 x 130mm x 5mm
- 12mm fixing holes

A post support fitting for installing timber posts and timber framework. The timber sits on the Post Support out of ground contact, which prevents rotting due to moisture from the ground. The height/level of the square support plate can easily be adjusted which is useful when building structures on uneven ground. Suitable for structurally supported timber posts and framework that need to last a long time e.g. for a basic timber porch or decking framework. Not recommended for free standing posts e.g. fence posts.

Installation: drill a 22mm diameter hole in the end of the timber post for the threaded bar to fit into, the depth of hole will vary depending on how much elevation is required. The post should sit firmly over the threaded bar down to the square support plate. The two nuts are tightened against each other to lock the support plate in the required position. The bottom of the post support is designed to be bolted down to a concrete base, we recommend using M10 Thunder Bolts.

- Welded construction, galvanised steel
- Total Height - 255mm
- Threaded bar - 22mm diameter
- Square support plate - 80 x 80mm x 4.5mm
- Bolt Down Plate - 80 x 80mm x 4.5mm
- 11mm fixing holes (x8)

A post support fitting for installing timber posts and timber framework. The timber sits on the Post Support out of ground contact, which prevents rotting due to moisture from the ground. The height/level of the square support plate can easily be adjusted which is useful when building structures on uneven ground. Suitable for structurally supported timber posts and framework that need to last a long time e.g. for a basic timber porch or decking framework. Not recommended for free standing posts e.g. fence posts.

Installation: drill a 22mm diameter hole in the end of the timber post for the threaded bar to fit into, the depth of hole will vary depending on how much elevation is required. The post should sit firmly over the threaded bar down to the square support plate. The two nuts are tightened against each other to lock the support plate in the required position. The bottom of the post support is designed to be bolted down to a concrete base, we recommend using M10 Thunder Bolts.

- Welded construction, galvanised steel
- Total Height - 255mm
- Threaded bar - 22mm diameter
- Square support plate - 100 x 100mm x 4.5mm
- Bolt Down Plate - 100 x 100mm x 4.5mm
- 11mm fixing holes (x8)

A post support fitting for installing timber posts. The post sits on the socket out of ground contact, which prevents the timber from rotting due to moisture from the ground. It is suitable for structurally supported timber posts that need to last a long time e.g. for a basic timber porch or lean-to. Not recommended for free standing posts e.g. fence posts.

Installation: drill an 18mm diameter hole in the end of the timber post for the Ground Socket to fit into, the hole needs to be at least 155mm deep for the post to sit firmly over the metal dowel down to the square support plate. The bottom of the ground socket is designed to be concreted into the ground, the cross bar ensures a secure fixing within the concrete.

- Welded construction, galvanised steel
- Total length - 600mm
- Fixing Dowel - 18mm diameter x 150mm
- Square support plate 100 x 100mm x 10mm
- Concrete-in section below support plate - 18mm diameter x 450mm
- Concrete-in 'cross bar' - 9mm diameter x 110mm across full width

A simple contempory handrail bracket, used for fixing handrails to walls and posts.

Wall fixing plate: 58mm diameter
Handrail fixing plate: 24 x 60mm
Bracket Length: 65mm (from wall to centre of handrail fixing plate)
Screw holes to suit 5.0mm countersunk screws
Electro-galvanised finish

Cost effective damp proof course for domestic construction
Suitable for use in horizontal and vertical applications
Safe and clean to handle and flexible even at low temperatures

BBA certified breather membrane. For use in cold non-ventilated pitched roof systems, also used in timber frame walls with timber, tile or slate outter cladding.

- 1m x 50m roll
- 140gsm
- Full specs. in the full description below
- BBA certificates in the downloads tab below

* Colour may vary

Everbuild 502 All Purpose Weatherproof Wood Adhesive is an effective resin based adhesive for all wood bonding. Suitable for internal and external use, it provides a high strength, impact resistant bond.
Ideal for all general woodworking and joinery uses, this adhesive is fast curing and dries clear.

The Everbuild Lumberjack 5min Polyurethane Wood Adhesive offers exceptional bond strength to wood and most common building surfaces. Suitable for bonding all common wood types (hard, soft, exotic, painted). It will also bond Formica, polystyrene, PU foam, metal and glass wool and various plastics (including PVC) to porous surfaces. These products also adhere to stone, concrete, brick and masonry. Products foam slightly on application to fill small gaps and increase overall bond strength.

Suitable for both internal and external use, with excellent weathering and ageing properties. They are also resistant to chemicals. Conforms to EN 204. D4 Strength.

Areas For Use

• General wood jointing and construction
• Window and door frame manufacture
• Door manufacture
• Furniture manufacture
• Construction of staircases and ladders
• As a high quality insulation adhesive for foam/glass wool/fibre boarding

The Everbuild Lumberjack 5min Polyurethane Wood Adhesive Gel is a thixotropic, transparent, gap filling gel which sets hard in just 5 minutes. Particularly suitable for equipment manufacture and production line applications where rapid handling is required. Conforms to EN 204. D4 Strength.

Everbuild General Purpose Silicone is a Multi-Purpose acetoxy cure silicone sealant that cures quickly to provide a permanently flexible, high strength waterproof seal. It contains a powerful anti-fungicide to prevent mould growth

BENEFITS
- Permanently flexible.
- Anti-fungal formula - prevents mould growth.
- Quick curing - low dirt pick up.
- Low viscosity for fast application.

AREAS FOR USE
- Sealing glass to glass.
- Sealing glass to aluminium and metal sealing.
- Sealing around baths, showers, basins and other sanitary ware.
- As an adhesive for fixing PVCu trims, cladding and panels.
- Sealing around worktops and laminates.
- Cap glazing to metal, timber and PVCu window frames, and pointing round window and door frames.
- For aluminium gutter sealing.
- General draughtproofing.

A cold applied oxidised bitumen based adhesive.
Used to bond roofing felt to most surfaces, sealing felt laps and as a cold gritting solution for bonding mineral chippings

Approx. coverage: 1.4m² / litre

A cold applied oxidised bitumen based adhesive.
Used to bond roofing felt to most surfaces, sealing felt laps and as a cold gritting solution for bonding mineral chippings

Approx. coverage: 1.4m² / litre (3.5m² / tin)

Injection resin used for anchoring threaded bar into concrete, stone, masonry, brickwork and hollow masonry.

- One mixer nozzle supplied per 300ml tube, extra nozzles available to purchase separately
- Two part resin, apply in one single action with a caulking gun
- Suitable for indoor and outdoor applications
- Colour: Grey

Spare nozzle for Exocet Polyester Resin