Fencing Materials

Slotted Concrete End Post; fully slotted on one side for timber fence panels and concrete gravel boards. Most fence panels will fit this post; check the slot dimensions below.

- Post Dimensions: 90mm x 110mm x 2700mm
- Slot Dimensions: 55mm (tapering to 50mm) x 23mm
- 56kg Each
- C50 Concrete (a strong mix)
- Four 5.5mm rebar set inside

These concrete gravel boards are designed to be used with recessed concrete posts. Concrete gravel boards for recessed posts give feather edge fencing a level surface to sit on. Raising feather edge boards on a gravel board will help prevent rot caused by ground moisture, gravel boards also help to prevent damage to fence panels caused by lawn mowers and strimmers.

- Dimensions: 50mm x 150mm x 2400mm
- 40kg Each
- C50 Concrete (a strong mix)
- Two 5.5mm rebar set inside
- One 14mm diameter hole in the middle to attach a support post (if required)

These concrete gravel boards are designed to be used with recessed concrete posts. Concrete gravel boards for recessed posts give feather edge fencing a level surface to sit on. Raising feather edge boards on a gravel board will help prevent rot caused by ground moisture, gravel boards also help to prevent damage to fence panels caused by lawn mowers and strimmers.

- Dimensions: 50mm x 150mm x 3000mm
- 52kg Each
- C50 Concrete (a strong mix)
- Two 5.5mm rebar set inside
- One 14mm diameter hole in the middle to attached a support post (if required)

Heavy duty concrete fence post for feather-edge fencing. This post has a weathered top; 3 recesses with bolt holes for fencing rails and bolt holes at the bottom to fit a gravel board. View image 2 for dimensions. This post is suitable for 1.35m feather edge boarding with a 150mm gravel board.

- Post Length: 2205mm
- Suitable for 1.35m Feather Edge + 150mm Gravel Board
- Three Recesses for 47 x 75mm Rail
- Use M8 x 180mm bolts to attach rails & gravel boards
- 67kg Each

Heavy duty concrete fence post for feather-edge fencing. This post has a back-weathered top, 3 recesses with bolt holes for fencing rails and bolt holes at the bottom to fit a gravel board. View image 2 for post dimensions. This post is designed to suit 1.65m feather edge boarding with a 150mm gravel board.

- Post Length: 2485mm
- Suitable for 1.65m Feather Edge + 150mm Gravel Board
- Three Recesses for 47 x 75mm Rail
- Use M8 x 180mm bolts to attach rails & gravel boards
- 73kg Each

Concrete repair spurs are used when a wooden fence post has snapped or rotted off at ground level. If the fencing above ground level is still servicable; extend the life of the fence by fitting a repair spur. Tips on how to fit a Repair Spur in 'Full Description' tab (below).

- Dimensions: 75 x 75 x 990mm
- Two bolt holes for M10 Carriage Bolts or M10 Coach Screws
- 14kg

Concrete repair spurs are used when a wooden fence post has snapped or rotted off at ground level. If the fencing above ground level is still servicable; extend the life of the fence by fitting a repair spur. Tips on how to fit a Repair Spur in 'Full Description' tab (below).

- Dimensions: 100 x 100 x 1220mm
- Three bolt holes for M10 Carriage Bolts or M10 Coach Screws
- 26kg

A premium quality Overlap Panel which is built to last.

Height: 914mm (3')
Width: 1829mm (6')

- Fully pressure treated panels
- Nailed construction
- Straight-edge, horizontal, sawn-finish slats
- Five vertical battens on both sides (approx. 16 x 38mm)
- Framed top and bottom on both sides (approx. 16 x 38mm)
- Finished and protected with a top capping strip
- These panels look the same from both sides, perfect for shared boundaries
- Manufactured in the U.K.

A premium quality Overlap Panel which is built to last.

Height: 1219mm (4')
Width: 1829mm (6')

- Fully pressure treated panels
- Nailed construction
- Straight-edge, horizontal, sawn-finish slats
- Five vertical battens on both sides (approx. 16 x 38mm)
- Framed top and bottom on both sides (approx. 16 x 38mm)
- Finished and protected with a top capping strip
- These panels look the same from both sides, perfect for shared boundaries
- Manufactured in the U.K.

A premium quality Overlap Panel which is built to last.

Height: 1524mm (5')
Width: 1829mm (6')

- Fully pressure treated panels
- Nailed construction
- Straight-edge, horizontal, sawn-finish slats
- Five vertical battens on both sides (approx. 16 x 38mm)
- Framed top and bottom on both sides (approx. 16 x 38mm)
- Finished and protected with a top capping strip
- These panels look the same from both sides, perfect for shared boundaries
- Manufactured in the U.K.

A premium quality Overlap Panel which is built to last.

Height: 1676mm (5'6")
Width: 1829mm (6')

- Fully pressure treated panels
- Nailed construction
- Straight-edge, horizontal, sawn-finish slats
- Five vertical battens on both sides (approx. 16 x 38mm)
- Framed top and bottom on both sides (approx. 16 x 38mm)
- Finished and protected with a top capping strip
- These panels look the same from both sides, perfect for shared boundaries
- Manufactured in the U.K.

A premium quality Overlap Panel which is built to last.

Height: 1829mm (6')
Width: 1829mm (6')

- Fully pressure treated panels
- Nailed construction
- Straight-edge, horizontal, sawn-finish slats
- Five vertical battens on both sides (approx. 16 x 38mm)
- Framed top and bottom on both sides (approx. 16 x 38mm)
- Finished and protected with a top capping strip
- These panels look the same from both sides, perfect for shared boundaries
- Manufactured in the U.K.

A heavy duty Close Board fence panel. Made in the U.K. using pressure treated, home grown softwoood.

Height: 1219mm (4')
Width: 1829mm (6’)

- 47 x 30mm framework
- ex. 22 x 125mm feather edge
- Nailed construction
- Pressure Treated green
- Finished with planed capping

A heavy duty Close Board fence panel. Made in the U.K. using pressure treated, home grown softwoood.

Height: 1524mm (5')
Width: 1829mm (6’)

- 47 x 30mm framework
- ex. 22 x 125mm feather edge
- Nailed construction
- Pressure Treated green
- Finished with planed capping

A heavy duty Close Board fence panel. Made in the U.K. using pressure treated, home grown softwoood.

Height: 1676mm (5'6")
Width: 1829mm (6’)

- 47 x 30mm framework
- ex. 22 x 125mm feather edge
- Nailed construction
- Pressure Treated green
- Finished with planed capping

A heavy duty Close Board fence panel. Made in the U.K. using pressure treated, home grown softwoood.

Height: 1829mm (6')
Width: 1829mm (6’)

- 47 x 30mm framework
- ex. 22 x 125mm feather edge
- Nailed construction
- Pressure Treated green
- Finished with planed capping

The Highgrove Tongue and Groove (V-joint) fence panel is a premium quality product, hand made in the U.K. It is made with planed finish, joinery grade, pressure treated redwood and has stainless steel fixings. This high-spec. product is very sturdy and built to last, offering a long-term, cost-effective fencing solution. We also stock a matching Highgrove pedestrian gate.

Height: 1219mm (4')
Width: 1829mm (6')

- Heavy Duty,
- Top & Bottom Rails: 45 x 95mm
- Intermediate Battens: 27 x 45mm
- Tongue & Groove (V-joint) cladding: ex. 19 x 125mm (approx. 14 x 115mm finished size)
- Planed finish, joinery grade redwood,
- Stainless steel fixings
- Pressure Treated with 15 year Treat-Right Warranty (view details in Downloads tab below)

The Highgrove Tongue and Groove (V-joint) fence panel is a premium quality product, hand made in the U.K. It is made with planed finish, joinery grade, pressure treated redwood and has stainless steel fixings. This high-spec. product is very sturdy and built to last, offering a long-term, cost-effective fencing solution. We also stock a matching Highgrove pedestrian gate.

Height: 1524mm (5')
Width: 1829mm (6')

- Heavy Duty,
- Top & Bottom Rails: 45 x 95mm
- Intermediate Battens: 27 x 45mm
- Tongue & Groove (V-joint) cladding: ex. 19 x 125mm (approx. 14 x 115mm finished size)
- Planed finish, joinery grade redwood,
- Stainless steel fixings
- Pressure Treated with 15 year Treat-Right Warranty (view details in Downloads tab below)

The Highgrove Tongue and Groove (V-joint) fence panel is a premium quality product, hand made in the U.K. It is made with planed finish, joinery grade, pressure treated redwood and has stainless steel fixings. This high-spec. product is very sturdy and built to last, offering a long-term, cost-effective fencing solution. We also stock a matching Highgrove pedestrian gate.

Height: 1829mm (6')
Width: 1829mm (6')

- Heavy Duty,
- Top & Bottom Rails: 45 x 95mm
- Intermediate Battens: 27 x 45mm
- Tongue & Groove (V-joint) cladding: ex. 19 x 125mm (approx. 14 x 115mm finished size)
- Planed finish, joinery grade redwood,
- Stainless steel fixings
- Pressure Treated with 15 year Treat-Right Warranty (view details in Downloads tab below)

The Milano fence panel is a good quality, well-made, decorative fence panel. It looks the same from both sides; perfect for shared boundaries. These panels are constructed with ‘hit & miss’ slats that allow wind to pass through. This panel has a smooth machined finish and is pressure treated green.

Height: 1200mm (approx. 4')
Width: 1800mm
Depth: 45mm

Please note: This panel is 1800mm wide, not 1829mm (6’), you can increase the panel width to 1829mm by attaching panel packing strips, sold separately.

The Milano fence panel is a good quality, well-made, decorative fence panel. It looks the same from both sides; perfect for shared boundaries. These panels are constructed with ‘hit & miss’ slats that allow wind to pass through. This panel has a smooth machined finish and is pressure treated green.

Height: 1800mm (approx. 6')
Width: 1800mm
Depth: 45mm

Please note: This panel is 1800mm wide, not 1829mm (6’), you can increase the panel width to 1829mm by attaching panel packing strips, sold separately.

The Neris fence panel is a good quality, well-made, decorative fence panel. It looks the same from both sides; perfect for shared boundaries. These panels are constructed with ‘hit & miss’ slats that allow wind to pass through. This panel has a smooth machined finish and is pressure treated green.

Height; middle of curve: 1200mm (approx. 4')
Height; edge of curve: 1000mm
Width: 1800mm
Depth: 45mm

Please note this panel is 1800mm wide, not 1829mm (6’), you can increase the panel width to 1829mm by attaching panel packing strips, sold separately.

The Neris fence panel is a good quality, well-made, decorative fence panel. It looks the same from both sides; perfect for shared boundaries. These panels are constructed with ‘hit & miss’ slats that allow wind to pass through. This panel has a smooth machined finish and is pressure treated green.

Height; middle of curve: 1800mm (approx. 6')
Height; edge of curve: 1600mm
Width: 1800mm
Depth: 45mm

Please note this panel is 1800mm wide, not 1829mm (6’), you can increase the panel width to 1829mm by attaching panel packing strips, sold separately.

The Reinas fence panel is a good quality, well-made, decorative fence panel. It looks the same from both sides; perfect for shared boundaries. These panels are constructed with ‘hit & miss’ slats that allow wind to pass through. This panel has a smooth machined finish and is pressure treated green.

Height; middle of curve: 1200mm (approx. 4')
Height; edge of curve: 1000mm
Width: 1800mm
Depth: 45mm

Please note this panel is 1800mm wide, not 1829mm (6’), you can increase the panel width to 1829mm by attaching panel packing strips, sold separately.

The Reinas fence panel is a good quality, well-made, decorative fence panel. It looks the same from both sides; perfect for shared boundaries. These panels are constructed with ‘hit & miss’ slats that allow wind to pass through. This panel has a smooth machined finish and is pressure treated green.

Height; middle of curve: 1800mm (approx. 6')
Height; edge of curve: 1600mm
Width: 1800mm
Depth: 45mm

Please note this panel is 1800mm wide, not 1829mm (6’), you can increase the panel width to 1829mm by attaching panel packing strips, sold separately.