Search
Fixings & Metalwork
M12 x 180mm Carriage Bolt
Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
75 in stock
From £1.12 Inc. VAT
M12 x 200mm Carriage Bolt
Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
89 in stock
From £1.22 Inc. VAT
M12 x 200mm Masonry Bolt
A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.
Drill Bit Dia. - 12mm
Anchor Length - 200mm
Washer Size - 14mm (M14)
Min Hole Depth - 85mm
Min Over Drill Depth - 25mm
Min. Embed Depth - 60mm
Max. Fixture Thickness - 140mm
Drill Bit Dia. for clearance - 14mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 19mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 80Nm
Drill Bit Dia. - 12mm
Anchor Length - 200mm
Washer Size - 14mm (M14)
Min Hole Depth - 85mm
Min Over Drill Depth - 25mm
Min. Embed Depth - 60mm
Max. Fixture Thickness - 140mm
Drill Bit Dia. for clearance - 14mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 19mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 80Nm
Stock Availability:
93 in stock
From £4.25 Inc. VAT
M12 x 220mm Carriage Bolt
Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
71 in stock
From £1.39 Inc. VAT
M12 x 300mm Carriage Bolt
Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
85 in stock
From £2.02 Inc. VAT
M12 x 50mm Carriage Bolt
Carriage Bolt; cup square hex, 30mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
150 in stock
From £0.58 Inc. VAT
M16 (16mm) x 1000mm BZP Threaded Bar
Mild steel threaded bar / studding.
- M16 (metric 16mm) thread diameter
- 1.0m length
- Mild steel grade 4.6
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
- M16 (metric 16mm) thread diameter
- 1.0m length
- Mild steel grade 4.6
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
Stock Availability:
19 in stock
£5.33 Inc. VAT
M16 (16mm) x 1000mm High Tensile Threaded Bar - BZP
High tensile threaded bar / studding.
- M16 (metric 16mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
- M16 (metric 16mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
Stock Availability:
Not in stock - This item is available to order.
From £7.87 Inc. VAT
M16 Form C Washer
A heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 34mm Diameter
17mm Bolt Hole: To suit M16 thread
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 34mm Diameter
17mm Bolt Hole: To suit M16 thread
Stock Availability:
269 in stock
From £0.22 Inc. VAT
M16 Hex Nut
Hex nut with metric thread, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Thread: 16mm - Metric
Depth: 12.5mm
Spanner Size: 24mm
BZP (Bright Zinc Plate) finish.
Thread: 16mm - Metric
Depth: 12.5mm
Spanner Size: 24mm
Stock Availability:
185 in stock
£0.18 Inc. VAT
M16 Square Plate Washer
A large heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 50mm x 50mm
17mm Bolt Hole: To suit M16 thread
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 50mm x 50mm
17mm Bolt Hole: To suit M16 thread
Stock Availability:
210 in stock
From £0.32 Inc. VAT
M20 (20mm) x 1000mm BZP Threaded Bar
Mild steel threaded bar / studding.
- M20 (metric 20mm) thread diameter
- 1.0m length
- Mild steel grade 4.6
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
- M20 (metric 20mm) thread diameter
- 1.0m length
- Mild steel grade 4.6
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
Stock Availability:
20 in stock
£8.15 Inc. VAT
M20 (20mm) x 1000mm High Tensile Threaded Bar - BZP
High tensile threaded bar / studding.
- M20 (metric 20mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
- M20 (metric 20mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
Stock Availability:
Not in stock - This item is available to order.
From £12.78 Inc. VAT
M20 Form C Washer
A heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 39mm Diameter
21mm Bolt Hole: To suit M20 thread
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 39mm Diameter
21mm Bolt Hole: To suit M20 thread
Stock Availability:
226 in stock
From £0.22 Inc. VAT
M20 Hex Nut
Hex nut with metric thread, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Thread: 20mm - Metric
Depth: 15mm
Spanner Size: 30mm
BZP (Bright Zinc Plate) finish.
Thread: 20mm - Metric
Depth: 15mm
Spanner Size: 30mm
Stock Availability:
183 in stock
£0.36 Inc. VAT
M20 Square Plate Washer
A large heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 50mm x 50mm
22mm Bolt Hole: To suit M20 thread
BZP (Bright Zinc Plate) finish.
Dimensions: 3mm x 50mm x 50mm
22mm Bolt Hole: To suit M20 thread
Stock Availability:
236 in stock
From £0.38 Inc. VAT
M5 x 50mm Hammer Fixing
A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 5mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 5mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Stock Availability:
31 in stock
From £0.07 Inc. VAT
M6 (6mm) x 1000mm High Tensile Threaded Bar - BZP
High tensile threaded bar / studding.
- M6 (metric 6mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
- M6 (metric 6mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
Stock Availability:
Not in stock - This item is available to order.
From £1.21 Inc. VAT
M6 Form C Washer
A heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Dimensions: 1.5mm x 13.5mm Diameter
6.5mm Bolt Hole: To suit M6 thread
BZP (Bright Zinc Plate) finish.
Dimensions: 1.5mm x 13.5mm Diameter
6.5mm Bolt Hole: To suit M6 thread
Stock Availability:
345 in stock
From £0.08 Inc. VAT
M6 Hex Nut
Hex nut with metric thread, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Thread: 6mm - Metric
Depth: 5mm
Spanner Size: 11mm
BZP (Bright Zinc Plate) finish.
Thread: 6mm - Metric
Depth: 5mm
Spanner Size: 11mm
Stock Availability:
438 in stock
£0.02 Inc. VAT
M6 x 100mm Roofing Bolt (+ Nut)
Roofing Bolt; designed for bolting through metal sheets but have many other uses.
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
Stock Availability:
184 in stock
From £0.29 Inc. VAT
M6 x 160mm Roofing Bolt (+ Nut)
Roofing Bolt; designed for bolting through metal sheets but have many other uses.
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
Stock Availability:
3 in stock
From £0.68 Inc. VAT
M6 x 30mm Roofing Bolt (+ Nut)
Roofing Bolt; designed for bolting through metal sheets but have many other uses.
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
Stock Availability:
313 in stock
From £0.11 Inc. VAT
M6 x 50mm Roofing Bolt (+ Nut)
Roofing Bolt; designed for bolting through metal sheets but have many other uses.
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
Stock Availability:
210 in stock
From £0.11 Inc. VAT
M6 x 60mm Hammer Fixing
A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Stock Availability:
144 in stock
From £0.12 Inc. VAT
M6 x 65mm Carriage Bolt
Carriage Bolt; cup square hex, 16mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
148 in stock
From £0.14 Inc. VAT
M6 x 70mm Coach Screw
Hex head coach screw, suitable for fixing into timber, can fix into brickwork and masonry with an M6 plug. M6 washers sold separately.
- Length excludes 4mm bolt head
- 55mm screw thread, 15mm unthreaded
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 2mm - 4mm pilot hole
- Hex Head fits a 10mm spanner
- Length excludes 4mm bolt head
- 55mm screw thread, 15mm unthreaded
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 2mm - 4mm pilot hole
- Hex Head fits a 10mm spanner
Stock Availability:
266 in stock
From £0.08 Inc. VAT
M6 x 80mm Hammer Fixing
A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 6mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Stock Availability:
167 in stock
From £0.18 Inc. VAT
M6 x 80mm Roofing Bolt (+ Nut)
Roofing Bolt; designed for bolting through metal sheets but have many other uses.
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
14mm bolt head, with 2mm cross-slots to fit flat head screw driver blade.
Supplied with one square nut, hex nuts and washers sold separately.
BZP finish (Bright Zinc Plate).
Stock Availability:
238 in stock
From £0.22 Inc. VAT
M8 (8mm) x 1000mm BZP Threaded Bar
Mild steel threaded bar / studding.
- M8 (metric 8mm) thread diameter
- 1.0m length
- Mild steel grade 4.6
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
- M8 (metric 8mm) thread diameter
- 1.0m length
- Mild steel grade 4.6
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
Stock Availability:
28 in stock
£1.58 Inc. VAT
M8 (8mm) x 1000mm High Tensile Threaded Bar - BZP
High tensile threaded bar / studding.
- M8 (metric 8mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
- M8 (metric 8mm) thread diameter
- 1.0m length
- High tensile steel grade 8.8
- Bright Zinc Plated finish (BZP)
- Nuts & washers sold separately
* This is a special order item, typically available within 1-2 working days
Stock Availability:
Not in stock - This item is available to order.
From £2.10 Inc. VAT
M8 Form C Washer
A heavy steel washer, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Dimensions: 1.5mm x 21mm Diameter
9mm Bolt Hole: To suit M8 thread
BZP (Bright Zinc Plate) finish.
Dimensions: 1.5mm x 21mm Diameter
9mm Bolt Hole: To suit M8 thread
Stock Availability:
403 in stock
From £0.11 Inc. VAT
M8 Hex Nut
Hex nut with metric thread, for general use with bolts and threaded bar (studding).
BZP (Bright Zinc Plate) finish.
Thread: 8mm - Metric
Depth: 8mm
Spanner Size: 13mm
BZP (Bright Zinc Plate) finish.
Thread: 8mm - Metric
Depth: 8mm
Spanner Size: 13mm
Stock Availability:
472 in stock
£0.07 Inc. VAT
M8 Nyloc Nut
Hex Nyloc Nut with metric thread, for general use with bolts and threaded bar (studding).
The Nyloc insert prevents accidental loosening caused by vibration.
BZP (Bright Zinc Plate) finish.
Thread: 8mm - Metric
Depth: 8mm
Spanner Size: 13mm
The Nyloc insert prevents accidental loosening caused by vibration.
BZP (Bright Zinc Plate) finish.
Thread: 8mm - Metric
Depth: 8mm
Spanner Size: 13mm
Stock Availability:
77 in stock
£0.05 Inc. VAT
M8 x 100mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
129 in stock
From £0.27 Inc. VAT
M8 x 100mm Hammer Fixing
A light duty fixing for jobs where speed of installation is important.
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 8mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Hammer fixings work in a similar way to screws and plugs, the hammer fixing screw has a special thread that can be hammered into the plug and loosened / screwed out if required.
Installation:
Pre-drill a 8mm pilot hole through the item that you're fixing and into the masonry or brickwork. Lightly tap the fixing through the pilot hole with a hammer until the plug is flush. EG. if you're fixing a timber wall plate, the plug fits inside the timber as well as the wall. Once the plug is flush with the timber, hit the head of the screw harder to drive it into the plastic sleeve until tight.
Minimum fixing depth: 45mm
Stock Availability:
139 in stock
From £0.24 Inc. VAT
M8 x 100mm Masonry Bolt
A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.
Drill Bit Dia. - 8mm
Anchor Length - 100mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 60mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm
Drill Bit Dia. - 8mm
Anchor Length - 100mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 60mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm
Stock Availability:
396 in stock
From £0.94 Inc. VAT
M8 x 130mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
120 in stock
From £0.34 Inc. VAT
M8 x 130mm Masonry Bolt
A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.
Drill Bit Dia. - 8mm
Anchor Length - 130mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 90mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm
Drill Bit Dia. - 8mm
Anchor Length - 130mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 90mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm
Stock Availability:
211 in stock
From £1.18 Inc. VAT
M8 x 150mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
149 in stock
From £0.37 Inc. VAT
M8 x 180mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
290 in stock
From £0.61 Inc. VAT
M8 x 200mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
194 in stock
From £0.66 Inc. VAT
M8 x 50mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
47 in stock
From £0.17 Inc. VAT
M8 x 50mm Coach Screw
Hex head coach screw, for heavy-duty applications. Suitable for fixing into timber, can fix into brickwork and masonry with an M8 plug . M8 washers sold separately.
- Length excludes 5mm bolt head
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 4 - 6mm pilot hole
- Hex Head fits a 13mm Spanner
- Length excludes 5mm bolt head
- Bright Zinc Plated finish (BZP)
- Pre-drill timber with 4 - 6mm pilot hole
- Hex Head fits a 13mm Spanner
Stock Availability:
254 in stock
From £0.11 Inc. VAT
M8 x 75mm Carriage Bolt
Carriage Bolt; cup square hex, 20mm mushroom head, BZP finish (Bright Zinc Plate). Designed for bolting through timber.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Square hex refers to the square section attached to the mushroom head, this sinks into timber and stops the bolt from spinning when the nut is tightened.
Supplied with one standard hex nut, washers sold separately.
Stock Availability:
143 in stock
From £0.22 Inc. VAT
M8 x 75mm Masonry Bolt
A self tapping bolt suitable for concrete, stone, brick, marble, wood and block (solid or hollow). Safe anchorage achieved without the need of high tightening forces. Can be removed and re-fixed into the same hole, providing the thread is correctly aligned. No expansion forces enables close to the edge fixing.
Drill Bit Dia. - 8mm
Anchor Length - 75mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 35mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm
Drill Bit Dia. - 8mm
Anchor Length - 75mm
Washer Size - 10mm (M10)
Min Hole Depth - 55mm
Min Over Drill Depth - 15mm
Min. Embed Depth - 40mm
Max. Fixture Thickness - 35mm
Drill Bit Dia. for clearance - 10mm (to prevent binding when tightening bolt)
Head Type - Hex Head, 15mm (Across Flats)
Driver Type - Impact driver, socket, spanner
Max Tightening Torque - 40Nm
Stock Availability:
380 in stock
From £0.82 Inc. VAT
Netting Clips, 1000 Pack - Galvanised
Pack of 1000 galvanised hog rings, for use with FP222 fencing pliers.
Netting clips (also known as Hog Rings) can be used to attach wire mesh and chainlink fencing to line wires, also used for mesh jointing and repairs.
Closed ring diameter: 5 - 11mm
Netting clips (also known as Hog Rings) can be used to attach wire mesh and chainlink fencing to line wires, also used for mesh jointing and repairs.
Closed ring diameter: 5 - 11mm
Stock Availability:
8 in stock
£8.99 Inc. VAT
Netting Clips, 1000 Pack - Green (PVC Coating)
Pack of 1000 green (PVC coating) Netting Clips for use with FP222 Fencing Pliers.
Netting clips (also known as Hog Rings) can be used to attach wire mesh and chainlink fencing to line wires, also used for mesh jointing and repairs.
Closed ring diameter: 5 - 11mm
Netting clips (also known as Hog Rings) can be used to attach wire mesh and chainlink fencing to line wires, also used for mesh jointing and repairs.
Closed ring diameter: 5 - 11mm
Stock Availability:
4 in stock
£11.99 Inc. VAT
Polyethylene Damp Proof Course - 100mm x 30m
Cost effective damp proof course for domestic construction
Suitable for use in horizontal and vertical applications
Safe and clean to handle and flexible even at low temperatures
Suitable for use in horizontal and vertical applications
Safe and clean to handle and flexible even at low temperatures
Stock Availability:
12 in stock
£4.78 Inc. VAT
Red Wall Plugs - Box of 100
Red plastic plugs, fix into concrete, brick and masonry by drilling a 5.5mm hole, suitable for use with woodscrews.
- Red wall plugs are suitable for No.6 - No.10 (3.5mm - 5.0mm) screws.
- Plug Length: 30mm
- Use a 5.5mm masonry drill bit
- Red wall plugs are suitable for No.6 - No.10 (3.5mm - 5.0mm) screws.
- Plug Length: 30mm
- Use a 5.5mm masonry drill bit
Stock Availability:
3 in stock
£0.96 Inc. VAT
Call us Monday - Friday 8am - 5pm. Saturday 8am - 12pm.
Payment options
